今天我们频率点名，其他友台把他的K6借我用一下顺便让我给他刷一个S表，然后刷到一半绿条不动了.....我心里也咯噔一下，我刷自己的K5就一点问题没有，现在的情况是转旋钮K6没反应了......求求友台们该咋办啊.......QAQ

不慌，只要能进入刷机模式，就继续刷。

@"BG8LGP"#p8816 现在倒还是能按住PTT拧开关亮刷机灯，但是电脑这边显示无法成功连接手台？

数据线的问题，检查耳机接口。检查电脑驱动。机子是刷不坏的，放心搞

@"BG9JFN"#p8820 我这条线刷自己的K5和GM338一点事没有，到K6这倒是能刷，但是刷机灯就闪几下就不闪了，然后显示升级失败

@"BI3EI"#p8888 我的K5刷机也经常这样，后面换一台电脑刷就正常了，你可以尝试下。

@"BI3EI"#p8888 那就是K6耳机插口的问题，把线头要么用力往里怼，要么稍微往外拔一下再试试

多刷几次，失败几次，说不定哪次就成功了，我遇到过

K6的K头有点紧，使点劲插到底，刷不坏放心刷

@"BI3EI"#p8815 断电放置一两个小时，然后刷官方固件，恢复出厂设置，在刷第三方

Oh no... I bricked someone else's K6!

BI3EI

Today, we're doing a frequency call-out. The other stations are lending me their K6s so I can also calibrate their S tables. However, about halfway through calibrating one, the green bar stopped moving... This made me realize something was wrong, as my own K5 worked perfectly. Currently, the rotary knob on the K6 isn't responding. Please advise! QAQ

Watermelon

BI3EI After a power outage lasting one to two hours, flash the official firmware, restore to factory settings, and then flash the third-party firmware.

BG8LGP

Don't panic; as long as you can enter the flashing mode, continue flashing.

BI3EI

BG8LGP Currently, I can still use the PTT to turn on the flashlight and operate the switch, but the computer is showing that it cannot successfully connect to the handheld device?

BG9JFN

Regarding the issue with the data cable, check the headphone jack.
Check the computer drivers. The computer is not easily damaged, so don't worry.

BI3EI

BG9JFN The K5 and GM338 on this line didn't have any issues. However, when I tried to flash the K6, the flashing light would blink a few times and then stop, followed by an "upgrade failed" message.

troilus

It seems like there's a problem with the cable.

BI7ALG

BI3EI I also experience this issue with my K5, but it resolves itself after I flash the device on a different computer. You can try this as well.

BG9JFN

BI3EI That's likely an issue with the K6 headphone jack. Try either pushing the cable end in firmly, or gently pulling it out slightly before trying again.

BG4IVY

I've tried several times before, failed a few times, but maybe one of those attempts will finally work. I've experienced that myself.

BG6UZM

The K6's K-head feels a bit tight, so apply some force to insert it fully. You can confidently use it for cleaning.

K1271

Mine also got bricked. When I tried to flash it, either the indicator light would flash a few times and then stop responding, or it wouldn't respond at all.

BG6HVC

You gained experience, while others got a new K6.

BI2UV

Even in the worst-case scenario, it can still be connected to a programming device; this thing really is like an indestructible little creature.

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起