我在使用X6100，发现电源线和DEV口线插入后，会在设备测试驻波时对数据造成影响这是插入DEV线至电脑时的驻波，可以到3左右 [upl-image-preview uuid=b396c956-eb43-4da1-a54e-8a661aac6606 url=https://storage.hamcq.cn/2025-06-04/1749044488-799518-20250604213832.jpg alt={TEXT?}] 拔掉DEV线后，驻波捡到1点多 [upl-image-preview uuid=4d5313a8-7358-4070-9708-fd33cfdbaf7d url=https://storage.hamcq.cn/2025-06-04/1749044538-590020-20250604213845.jpg alt={TEXT?}] 然后，下面是插入外接电源时的驻波，数值在2左右 [upl-image-preview uuid=05cd4d42-dab6-478e-9326-20cac9eacb62 url=https://storage.hamcq.cn/2025-06-04/1749044582-272350-20250604213854.jpg alt={TEXT?}] 拔掉外接电源后，驻波降到1左右 [upl-image-preview uuid=11984321-af35-4608-9a4f-6d68786875ba url=https://storage.hamcq.cn/2025-06-04/1749044614-680941-20250604213849.jpg alt={TEXT?}] 请问，这个因为电源与USB线引起的驻波变化，对发射有没有影响？可以通过添加**磁环**或**扼流巴伦**或其他办法来解决吗？

您这三张图频率不一样。。。在同一频率下这么测试，驻波有起伏吗？另外似乎天调是开着的？

@"Ethan"#p68497 嗯，天调开着的。它是机器自身的程序，在扫描频段内的驻波，所以频率是变化的。

@"BI3BGM"#p68508 额。。测驻波是不是先把天调关了。。。用的啥天线？14兆可能会窄点，感觉扫描区间有点大所以驻波有浮动？

@"Ethan"#p68512 天调不关也不碍事，插拔对应线材，扫描的驻波，有明显变化。

嗯，试试做好电台的接地，电台有一个专门的接地螺丝。

@"BI3BGM"#p68515 做个接地加加磁环试试吧。。兴许有用🤔

电源是开关电源不是电池的话检查下家里插座有没有接地吧 P.S. 电台接地不是接在市电的地上，更不能接在煤气管上

Can the X6100's loop instability be resolved by adding a magnetic loop, a choke balun, or other methods?

BI3BGM

我在使用X6100，发现电源线和DEV口线插入后，会在设备测试驻波时对数据造成影响

这是插入DEV线至电脑时的驻波，可以到3左右

拔掉DEV线后，驻波捡到1点多

然后，下面是插入外接电源时的驻波，数值在2左右

拔掉外接电源后，驻波降到1左右

请问，这个因为电源与USB线引起的驻波变化，对发射有没有影响？可以通过添加磁环或扼流巴伦或其他办法来解决吗？

Ethan

The three images you provided have different frequencies... Would you observe oscillations in the standing wave when testing at the same frequency?
Also, it seems like the weather radio was on?

BI3BGM

Ethan Yes, the engine is running.
It's a program within the machine itself that generates standing waves within the scanning frequency range, so the frequency changes.

Ethan

BI3BGM
Um... does measuring standing waves require turning off the antenna first?
What antenna are you using? The 14 MHz band might be quite narrow, and I'm getting a feeling that the scanning range is too large, which could explain the fluctuations in the standing wave ratio.

BI3BGM

Ethan The antenna was not connected or disconnected, and it did not interfere with anything. When scanning, there were noticeable changes in the standing wave.

Ethan

BI3BGM
Try adding a grounding wire and a magnetic ring. It might help.🤔

BG8AMG

Okay, let's try to properly ground the radio. The radio has a dedicated grounding screw.

BG5ELQ

If your power source is a switch-mode power supply and not a battery, check if the electrical outlet in your home is properly grounded.
P.S. Radio grounding should not be connected to the ground of the mains electricity supply, and certainly not to a gas pipe.

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起