机器是协谷g90。ft8音量始终显示是关闭的。手动打开也是瞬间自动关闭。用手咪发射功率显示是0求助各位大神到底是什么原因

ft8如果使用了端馈天线会出现各种稀奇古怪死机的毛病。首先重启不连接电脑试试机器发射接收是否正常如果不正常可以初始化一遍依然不正常就返厂吧协谷售后还不错啥毛病都能修返厂一次两百元。

早上又试了一下，usb模式是有功率的，u-d模式掐手咪没反应，连电脑音量就是打不开，音量那个标识就是一个x，强行拉到100%也瞬间掉回成关闭

@"bi3apz"#p65588 U-D模式手咪应该就不起作用了

@"bi3apz"#p65556 我也遇到过类似的情况，我觉得大概率是电脑端设置的问题，可以试试用手机FT8是否正常，如果要正常说明电台基本没问题，试试调整电脑端声卡设置和软件设置。也可以试试电脑安装最新声卡驱动尝试一下

@"BH4FRV"#p65606 驱动应该是没问题，为了这个还得再买个蓝牙适配器😦

@"bi3apz"#p65635 电台设置成U-D模式，音频输入选择line，用vox语言激活，只接一根acc线

@"BD8FTC"#p65651设置是这样的，接线不是需要两根吗？机头一个usb，耳机插孔一个acc

@"bi3apz"#p65676 用vox激活后就不需要usb了，电脑输出语音就自动发射了

The g90 transmitter has no power.

bi3apz

The radio is a XieGu G90. The transmit volume always shows as "off." Manually turning it on also results in it immediately turning off. When using the handheld, the transmit power display shows 0. Please help! What could be causing this?

BH4FRV

bi3apz I have also encountered similar situations. I believe that the problem is most likely due to settings on the computer side. You can try using FT8 on your phone to see if it works normally. If it does, this indicates that the radio itself is probably fine. Then, you can try adjusting the audio and software settings on your computer.
You can also try installing the latest sound card drivers on your computer to see if that resolves the issue.

BG6RCW

If using an end-fed antenna with FT8, you may experience various strange and inexplicable malfunctions. First, try restarting the device without connecting it to a computer to see if it still functions normally. If it doesn't, try initializing it again. If it still doesn't work, send it back for repair. XieGu's after-sales service is quite good; they can fix almost any problem. The cost of returning it for repair is around 200 yuan.

bi3apz

I tried again this morning, and the USB mode is working with power. However, when I switched to the U-D mode, the microphone didn't respond at all, and neither did the computer's volume control. The volume indicator shows an "X," and even when I manually increase it to 100%, it immediately drops back to being off.

BH4FRV

bi3apz The U-D mode microphone should no longer function.

BI4IVE

How about you trade your K6 with me?

YofoaStudio

If that doesn't work, try using a wireless connection.

BG2EWI

BH4FRV Yes, the data mode audio stream goes through the DIN port at the rear, not the microphone input.

bi3apz

BH4FRV The driver should work fine; however, I'll need to buy a separate Bluetooth adapter for this.😦

BD8FTC

bi3apz Set the radio to U-D mode, select "line" for audio input, activate it using Vox language, and only connect one ACC cable.

bi3apz

BD8FTCThe settings are as follows: The wiring requires two cables, right? One USB on the front and one ACC port on the headphone jack.

BD8FTC

bi3apz Once Vox is activated, you no longer need a USB device; the computer's audio output will automatically transmit speech.

BG2EWI

What method is used to connect a computer to a radio?

bi3apz

BG2EWI Connect the headphone cable to the ACC port at the back of the butt, and connect the USB cable to the communication interface on the side of the head.

BG2EWI

bi3apz It's strange; according to my understanding, this connection method shouldn't cause the volume bar on the computer to not move up.

bi3apz

BG2EWI Yes, it's strange. I bought a C-mouth to 3.5mm connector and tried using it with my phone.

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起