如题，昨天出门去爬山，朋友带了一对小巧的傻瓜对讲机，只能加减频道，没有显示屏，我用8800自带的扫描对频，显示NONE亚音，确认亚音关闭，频道一致，只能接收，我说话傻瓜对讲机就是收不到。回来我测试用我另外的UV83对频，同样的方法和参数，可以正常收发。去抖音搜索了一下，有很多人遇到同类问题，目前初步结论： 1.目前排除是我机器的问题和设置问题。 2.如何排查傻瓜对讲机问题原因？有没有火腿遇到过这种问题？

多扫描一会说不定有亚音其次就是对面是非标亚音那就没招了非标是无解的

@"BG2EFX"#p52903 扫描了很多次，都是NONE，我切换到傻瓜对讲机其它频道，有扫描识别出来亚音，我用这个有亚音的频道对频了也没法通信，挺奇怪的。没有其它设备排查。

有频差吧，写频线插上看看

The Senhaix 8800 Pro only works with a dummy radio; it can only receive, but the transmitting party cannot receive.

BG5FEE

As the title indicates, yesterday I went hiking with a friend who brought a small, non-digital walkie-talkie. It could only adjust frequencies and had no display screen. I used the built-in scanner on my 8800 to scan for frequencies, and it showed "NONE" at a sub-audible frequency. After confirming that the sub-audible frequency was off, and that the channels were consistent, I realized that I could only receive; however, when I spoke into the walkie-talkie, it didn't pick up my voice.
When I returned home, I tested with my other UV83 radio using the same method and parameters, and it worked normally for both sending and receiving.
I searched on Douyin and found that many people were experiencing similar problems. My preliminary conclusion is:
1. Currently, the issue seems to be related to my machine and its settings.
2. How to troubleshoot the cause of problems with a simple walkie-talkie?
Have you ever experienced this problem with ham?

BG2EFX

Scan for a while; maybe you'll find something below audio frequency.
Secondly, if the other side is using a non-standard Yamaha, then there's no way to proceed. Non-standard equipment is essentially unsolvable.

BG5FEE

BG2EFX I scanned multiple times, but all results were "NONE." When I switched to a different channel on the dumb radio, I was able to detect sub-audible frequencies. However, even when I used that channel to transmit, I couldn't establish communication. This is quite strange. I have not tested with any other devices.

BG5FEE

BG2EFX I scanned multiple times, but all results were "NONE." When I switched to a different channel on the dumb radio, I was able to detect a weak signal. However, even when I used that channel to transmit, I couldn't establish communication. This is quite strange. I have not tested with any other devices.

BG5FEE

BG2EFX I scanned multiple times, but all results were "NONE." When I switched to a different channel on the dumb radio, I was able to detect sub-audio frequencies. However, even when I used that channel to transmit, I couldn't establish communication. This is quite strange. I have not tested with any other devices.

BG5FEE

BG9JDI

There should be a frequency difference; try plugging in a frequency line to see if it works.

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起