今天下午使用协谷 6100 便携电台，20 米端馈天线使用 FT8 模式，能正常接收的大家的信号，但发射的时候 5w 和 10w 都呼不到人，想请大佬给分析一下是功率不行还是天线不行，还是说地理位置不行[upl-image-preview uuid=b9ef3b3e-725a-41cb-ae1f-c8bbd09bfceb url=https://storage.hamcq.cn/2025-01-04/1735991266-456148-3a5144b253cd7dab5fc236b0d85d9b8.jpg alt={TEXT?}] [upl-image-preview uuid=00a25c02-0c40-4c98-870a-f9c42d3ef192 url=https://storage.hamcq.cn/2025-01-04/1735991271-843137-0ad8076a20ee23198b736c7ba3e1ea1.jpg alt={TEXT?}] [upl-image-preview uuid=9b473696-60be-469e-b008-b330e7a657a4 url=https://storage.hamcq.cn/2025-01-04/1735991267-334048-3eca5bbfab9d2aaa9bd86a339fc4e4b.jpg alt={TEXT?}] [upl-image-preview uuid=9508518e-c756-412b-ae50-f051aefceabd url=https://storage.hamcq.cn/2025-01-04/1735991381-955854-da615c513cd39fa55f3ccbbbb7215ff.png alt={TEXT?}]

都没输出当然叫不到了... [upl-image-preview uuid=177c50e8-74dc-4655-81a7-dee0157cf8af url=https://storage.hamcq.cn/2025-01-04/1735991789-215810-image.png alt={TEXT?}]

是不是因为没开输出 [upl-image-preview uuid=177c50e8-74dc-4655-81a7-dee0157cf8af url=https://storage.hamcq.cn/2025-01-04/1735991789-215810-image.png alt={TEXT?}]

@"BG5VLI"#p48749 啊，后面我拉上去了，拉到顶也是显示0

@"BI6OIE"#p48750 神奇，用的vox还是ptt? ptt的话频率那块是红色，感觉配置可能有问题

@"BG5VLI"是按说明书资料上设置的，也是第一次用，看着哔哩哔哩M哥和一个UP主的视频学的 [upl-image-preview uuid=8c091bb9-be11-4203-8227-a2c11943c976 url=https://storage.hamcq.cn/2025-01-04/1735992524-691705-image.png alt={TEXT?}] #p48751 [upl-image-preview uuid=f2a2df79-ad5f-42b3-808e-befc6edeb952 url=https://storage.hamcq.cn/2025-01-04/1735992647-583483-image.png alt={TEXT?}] [upl-image-preview uuid=3390334d-d167-47eb-bb84-31514607e1af url=https://storage.hamcq.cn/2025-01-04/1735992674-348931-6f3ac51e089c180e989bfb87925dfdf.jpg alt={TEXT?}]

用Hamalert看看有没有人收到你的呼叫，没有spot的话说明信号没出去。然后检查下控制面板里面的系统音量，有时候莫名其妙电台声卡的扬声器就打叉了。

信号确实没出去， [upl-image-preview uuid=9820b3fc-cfc3-46b7-a2a8-7b008c0b74ba url=https://storage.hamcq.cn/2025-01-04/1735994658-835046-image.png alt={TEXT?}] 突然想起x6100自带声卡，直接typec插上就能用，是不是系统设置把声卡静音了？

@"Liridice"#p48758 好的！我再看看，谢谢

@"BG5VLI"#p48761 好的，谢谢！

你看看机器发射的时候有没有功率

I can receive FT8 signals but cannot make contact with anyone; is this due to the radio itself, or a problem with the antenna system?

BI6OIE

bg2kud Okay.👌I'm moving to a different location.

BI6OIE

BG2EWI Okay, thank you very much, I will try it out this afternoon.

Passerby

You can try the firmware I compiled. https://forum.hamcq.cn/d/4271 （

BI6OIE

Passerby Thank you for sharing this! I'll download it and try it out.

Liridice

BI6OIE Does the X6100 show up on a spectrum analyzer when transmitting in other modes? If so, please look at the spectrum while using FT8.

BI6OIE

Liridice Received, the spectrum power is fine... I've updated to the new firmware now.

ABCDEFG

BG2EWI In other words, it only shows up after someone has accepted my signal.

BG4IJK

ABCDEFG As long as a friend in Taiwan has enabled automatic reporting and received your signal, regardless of whether they respond to you or not, it will be displayed there.

BG2ELG

ABCDEFG Yes, because there are so many people using FT8, and it's all software-based with a high degree of automation, it can be used to indirectly monitor the propagation of your own signals.

BI6OIE

Over the past few days, I have followed the suggestions from several experts and systematically checked each issue. Today, I have confirmed that I can successfully perform FT8 operations. Below, I will share the problems I encountered and their solutions for your reference:
Solution
1. If the radio does not have any special settings, it is recommended to restore it to its factory default settings and then download the latest firmware released on September 15, 2024, from the official website for updating.https://www.cqxiegu.com/zlxz）

2、Attach a magnetic ring to all connecting cables.

3. Note that JTDX is listening on VFOA, but does it switch to VFOB channel for transmission? This might be due to previous incorrect settings. It's possible to configure JTDX.(Lock Tx = Rx)In the diagram, the blue arrow section – the simplest solution is to restore it to factory settings. The green arrow's power number will be displayed during transmission, but I always see 50W, even though my actual output is only 5W...

Problems encountered since installing rack number 4
On the 4th, while setting up an outdoor station, I observed that JTDX could receive signals but failed to send any replies, and also noticed that the computer's case was live.
In the afternoon of the 5th, I took an extra data cable based on the suggestions from everyone, and then observed the waterfall chart and power levels during transmission. Everything was fine (except for the incorrect frequency!), but after trying twice, I realized that it was due to receiving and transmitting at different frequencies. Therefore, I adjusted the JTDX.(Lock Tx = Rx)After successfully connecting to two other stations, I suddenly received error messages for audio input and output. Changing the cable didn't help, and I couldn't find a USB audio interface in the settings either. After struggling for a while, I gave up and went home. I then updated the firmware and attached a magnetic ring to the cable.
After using the new firmware again in the afternoon on the 6th, there were no further errors reported. Once connected, all breast implants were successfully activated.

I hope everyone has a great time playing!

BG2EWI

BI6OIE The mammary ducts are now all open.

Treating complex and difficult cases with FT8

Passerby

BI6OIE
I feel that using a direct FT8 implementation on the WSPR rig would be preferable, so I'd recommend trying this alternative firmware.

BI6OIE

Passerby Yes, yes! My gaming laptop only lasts for about an hour, so I don't dare to go too far. Also, the electromagnetic environment nearby is very poor, so if you have one built-in, just bring a large power bank!

BG2ELG

It is not recommended to transmit and receive on the same frequency, for example, if you respond to someone's CQ and successfully establish communication, but then do not manually switch to a different frequency, continuing to listen on their frequency, this will interfere with other radio operators attempting to communicate.

BI6OIE

BG2ELG Received🫡I have already fixed it. After updating the firmware, I no longer experience the previous issues, so I no longer transmit and receive on the same frequency.

BI4MIG

I'm seriously considering buying one of these X6100s after seeing it.
My personal opinion: The X6100 looks better than the X6200.

« 上一页

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起