The G90N transmitter shows full power, but the actual tested power is very low.

BG5VLI

前两天玩ft8发现一个人都叫不到，想着是不是天馈出问题了，查看了一下并无异常，到电台旁低头一看显示满功率，但是有一股奇怪的味道传出，一开始还在想是不是手上涂药的味道，后面才意识到是不是电台烧了，奈何没有功率计无法测试，于是昨天请一位本地友台帮忙守听了一下，即使功率开到最大（电台上也显示满功率），声音还是和蚊子叫一样（平常打ft8都能给到+7），请问一下各位大佬这种情况是功放管烧掉了吗？

CQ-BG8LTU

The performance of my handheld V-band amplifier was as follows: it burned out, and I have already sent it in for repair.
I assume it's the same for you too.

BI4PMQ

Without a power meter, it's impossible to measure the transmit current and determine if there's a problem.

Bi4KKF

It's fine to use a dummy load; just test it out and check the temperature. A 5W dummy load should be sufficient.

BI4PMQ

Bi4KKF Is there a way to test this with my tongue?

BG7NOD

BI4PMQ Please change your profile picture to a dog. Thank you.

Bi4KKF

BI4PMQ The tongue is best suited for licking the very end of the oscillator.

BI4PMQ

BG7NOD That's completely inappropriate. What I was saying makes sense, doesn't it?

BG5VLI

Thank you for your helpful responses. I have already returned it to the factory for repair.

bg2kud

I have a 90S, and I'm not sure how to handle the cooling for the G90N.
Here's what I experienced using the XieGu G90S in the 1990s: The voice and CW functions worked perfectly on the XieGu G90S. However, transmitting data with power exceeding 5W for extended periods could easily damage the amplifier.
Currently, I'm using a 1W amplifier. Two powerful fans are running. It hasn't had any issues for over a year.

BG5VLI

bg2kud That's true, but the cost of a receiver would be enough to buy a used radio.😥

BG2EWI

bg2kud 啊？我之前都是G90S满功率挂一整天FT8的😂

BG7NOD

Bi4KKF Also, please change your profile picture to a dog. Thank you.🙀

BH9FPK

Bi4KKF No need for the tongue; just use your hands. The antenna is working well, g106c, and FT8 is running automatically. I was thinking about adjusting the center frequency to be higher, so I connected a 10cm wire in front. As I was tightening the connection, the other end started transmitting. Wow, it's biting!

BG5VLI

返修结果：未损坏，厂家重新刷了一下固件，寄回来后试了一下又能正常使用了，太奇怪了，难道是我无意中更改了什么设置吗，可是我明明试过重置设置来着😥

BI4PMQ

BG5VLI Perhaps it was due to the poor communication during those days.

BG4ILW

The firmware that comes with the device is compliant G90N firmware, which displays 20W, but it can only transmit up to 15W. Only by flashing the G90S firmware can the display be truly accurate.

BG9CHE

BG4ILW The original factory firmware for the 90N limits the transmission power to 10W, while the head unit can be adjusted to 20W because the head unit has the same firmware as the 90S. However, if the main unit is not flashed with the 90S firmware, the maximum output will still only be 10W.

BI4PMQ

BH9FPK If 5 watts can bite someone, then what about 100 watts?😂

BH9FPK

BI4PMQ 100 watts, RF burns, ... There was an incident where a 5-watt BaoFeng unit caused burns. The antenna was damaged, and when the finger touched the contact point on the antenna, it triggered the RF output, also causing a bite.

BG4TRF

I used a power meter to measure it, and the maximum power is 90N, which is about 15W. 20W is definitely not enough. In actual use, there's no difference; as long as the system can output 10W, I'm satisfied.

BG5VLI

BG4TRF 可能是早就猜到有人会刷g90s的固件，干脆先从硬件层面限制了🤪

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起