最近几次通联友台普遍报告断续，也没细看指示灯，今天才发现指示灯偶发性不亮，PTT需要大力出奇迹才能保持发射，不断续就怪了，尴尬😓

@"HawkeTallweiss"#p31591 有些机器的PTT按钮很硬，需要特别大的力气才能按下去，手指稍微松一点就会断开，但这也似乎是一个优点，避免误触。不过有些低端机器的PTT按钮会因为触点氧化或良率等原因，即使是不需要很大力气按着，但有时候手指松一点就会虚接

@"BG2EWI"#p31720 一开始我也以为是故意设计的防误触，不过我这个应该就是坏了接触不好，按键的咔哒手感已经出来了，但是还没有接通，需要继续往下按下去，已经返厂维修了

@"HawkeTallweiss"#p31804 是的，我那台摩托罗拉的GP338plus的PTT按钮就是很硬，刚上手的时候按了一下甚至没按动，不过习惯也就好了。虽然不容易按下去，但是按键的段落感十分分明，如果感觉到了段落感但还是不好使，那就是触点问题了

有的手台PTT键很硬，没按几下手指头都按疼

@"BG2EWI"#p31820 返厂维修结果出来了，解释是使用的锅仔片都会有这种现象，和其他正常新机没区别😂，属于我操作问题，勉强接受了

可以考虑整一个手咪😆还可以减少PTT键的使用损耗

@"HawkeTallweiss"#p32123 锅仔片通病，密封不严进入水分，或者PCB焊盘氧化了，按下去就会导致接触不良

撕开锅仔片,用酒精擦金手指和锅仔片反面部分,有必要的情况下可以上砂纸磨或者直接万能的WD40喷一下不过时间长了氧化了还是会接触不好

@"BI7KGD"#p32253 用橡皮蹭几下就行，我鼠标里的静音按键也是类似锅仔片的结构，时间长了钢片氧化失灵，拆开用橡皮擦干净再装回去就好了

Intermittent connectivity doesn't necessarily mean poor signal; it could also be due to a PTT malfunction.

HawkeTallweiss

Recently, I've noticed intermittent communication with several amateur radio operators. I haven't paid close attention to the indicator lights, but today I discovered that they are occasionally not illuminating. It seems that maintaining a continuous transmission on PTT requires significant effort and is unreliable. This situation is quite frustrating.😓

BG2EWI

HawkeTallweiss Some of the PTT buttons on these machines are quite stiff, requiring a significant amount of force to press, and if you release your finger slightly, it will disconnect. However, this also seems to be an advantage, as it prevents accidental activation. But some low-end models have PTT buttons that can become intermittent due to oxidation or other factors, even though they don't require much force to press; however, sometimes releasing your finger slightly can cause them to become temporarily disconnected.

HawkeTallweiss

BG2EWI Initially, I thought it was intentionally designed to prevent accidental presses. However, it seems like my one is simply broken and doesn't make good contact. The clicky feel of the buttons has returned, but it's not connecting properly. I need to press further down to activate it, and it has already been sent back for repair.

BG2EWI

HawkeTallweiss Yes, the PTT button on my Motorola GP338plus is quite stiff. When I first used it, I had to press it several times before it worked. However, after getting used to it, it became easier to use. Although it's not easy to press, the key has a very distinct tactile feel. If you feel the tactile feedback but still can't use it, then there is likely a problem with the contact points.

HawkeTallweiss

BG2EWI The results of the factory repair have come in. The explanation is that the ceramic plates used in the product exhibit this phenomenon, and it's no different from normal new units.😂This was due to my own operational issues, and I could accept it with some difficulty.

BA4QBB

Some handheld radios have very stiff PTT (push-to-talk) buttons, which can cause finger pain after only a few presses.

BG2EWI

HawkeTallweiss A common problem with "Guo Zi Pian" (a type of electronic component) is that it seals poorly and allows water to enter, or that the PCB pads have oxidized. Pressing the button then causes poor contact.

BI3TJT

Consider building a complete hand-held microphone system.😆It can also reduce the wear and tear on the PTT button.

BI7KGD

Tear open the pot scraper, use alcohol to clean the gold finger and the back of the pot scraper, and if necessary, use sandpaper to smooth it.
Or simply spray WD-40 all over it.
However, over time, oxidation can still lead to poor contact.

BG2EWI

BI7KGD Just wipe it with a rubber eraser, and the mute button on my mouse also has a similar structure to a small metal plate. Over time, the metal plate oxidizes and becomes unusable. Simply open it up, clean it with a rubber eraser, and then reassemble it, and it will be fine.

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起