[upl-image-preview url=https://storage.hamcq.cn/2024-02-06/1707207643-782781-image.png] 使用JTDX，都设置好了，监听是正常的，发射直接报错： Hamlib 错误: 被无线电设备拒绝的命令当设置PTT 开启机器上会A\B信道来回跳

6100啊，用手机玩吧，我连电脑也是不好使。手机安装FT8CN，一根USB OTG线就行了，方便的很

@"BI1LWR"#p10037 我也很奇怪，之前在设置还是好好的，最近升级了x6100的固件后就不行了~ 果然还是手机方便，直接使用x6100的wifi加wfserver功能无线连接控制

@"Jason"#p10040 你的无线好用吗？我的6100无线一会就挂，6100的无线服务不稳定好像

@"BI1LWR"#p10042 目前链接还行，没断开过，不过没怎么发射，守下6m看看有没有传播😄

@"bi1pwk"#p10657 我也是同样问题，jtdx就是不行，回头试试你的方法

@"bi1pwk"#p10657 我也得试试，q900也有这个问题，厂家回复1.接地2.加磁环，都做了还是出现，回头试试

@"Bi4KKF"#p10721 我之前也尝试过加磁环接地，我甚至把电台输出功率设置到0.1w，但是仍然出问题，我把输出天线换成假负载，还是不行。这么低的功率以及标准的50Ohm负载，理论上不应该再出现干扰，所以后面开始排查软件问题。我没用过q900这个机器，不过排查思路应该大致相同。你也可以按照我的方式查一下。

现在基本上就用手机了，电脑上的不管wsjtx还是jtdx都会出现断联的情况，手机有时候也会断开，一直弄不明白是哪里的问题

我手机用线连接6100，只能在7M、14M玩，到21M守听可以，一发射就连接断掉了，加磁环也没用，干扰太大

@"bi1pwk"#p10657 刚试了下可以发射了，感谢大佬指点

XieGu X6100 FT8 transmission failed.

Jason

I have set up JTDX and everything seems to be working correctly. However, when I try to transmit, I get an error directly.

Hamlib Error: Command rejected by radio device When PTT is enabled

The machine switches between A and B channels repeatedly.

BI6OIE

Jason 我也遇到了A/B信道跳的问题，FT8发射时会忽然变信道.....换了9月最新固件解决了

BI1LWR

6100, let's play on my phone instead. I can't even get it to work on my computer.

With FT8CN installed on my phone, all I need is one USB OTG cable, which makes it very convenient.

Jason

BI1LWR I'm also very puzzled, it was working fine before, but after upgrading the firmware of the X6100 recently, it stopped working.

As expected, using a mobile phone is still convenient; I can directly use the x6100's Wi-Fi and wfserver features to establish a wireless connection for control.

BI1LWR

Jason Is your wireless connection working well? My 6100 wireless connection keeps dropping, and the 6100 wireless service seems to be unreliable.

Jason

BI1LWR Currently, the link is still working and hasn't been disconnected. However, it hasn't been used much; I'll try transmitting on 6m to see if there's any propagation.😄

bi1pwk

我也是x6100，用jtdx，总是遇到发射时断开的问题。经过非常多排查，发现，wsjtx和ft8cn都可以用，就是jtdx不行。排除电台问题。
本人使用windows系统。测试后，将wsjtx安装目录下面名为libhamlib的dll文件替换到jtdx的安装目录下，再次尝试，问题解决。

BI1LWR

bi1pwk I'm experiencing the same issue; jtdx doesn't work either. I'll try your method later.

Bi4KKF

bi1pwk I'll also try this, and I've experienced a similar issue with the Q900 as well. The manufacturer suggested grounding and adding a magnetic ring, but even after doing that, the problem persists. I'll try it out later.

Jason

bi1pwk Just tested it, and it works! Thanks for pointing that out.

bi1pwk

Bi4KKF I had also tried adding a magnetic loop ground, and I even set the radio's output power to 0.1W, but it still didn't work. When I replaced the output antenna with a dummy load, it was still no use. With such low power and a standard 50 Ohm load, interference shouldn't occur theoretically, so I started troubleshooting software issues. I haven't used the Q900 machine before, but the troubleshooting approach should be similar. You can also try troubleshooting in the same way.

BI1IPB

Currently, I'm mainly using my phone. Both wsjtx and jtdx on my computer keep disconnecting, and sometimes even my phone disconnects. I can't figure out what the problem is.

BI1LWR

When using my mobile phone to connect to the 6100 via a cable, I can only operate at 7 MHz and 14 MHz. However, it works fine at 21 MHz for listening. But as soon as I start transmitting, the connection immediately drops. Adding a magnetic loop doesn't help either; the interference is too strong.

bi1pwk

Jason Actually, switching DLLs isn't very stable; I recommend using FLRIG to control the radio and then linking it with JTDX.

Jason

Now, I'm not sure what's going on. After connecting my phone and computer, it disconnects immediately after transmitting. I also added a few magnetic rings to the USB cable, but the wireless connection is sometimes good and sometimes bad.

BD7PRI

I'm experiencing this issue with the G90s Vox, and adding a magnetic loop doesn't help. The only solution I've found is to move the antenna further away.

BG6SQI

Later, I switched to a different version of JTDX, and it worked perfectly.

Jason

BG6SQI Which version did you upgrade to?

pmxlbt

Why can my 6100 decode and transmit using FT8CN, but doesn't output any power when transmitting?

Jason

pmxlbt If there's no power output, it means the audio isn't going through. Check the audio output options.

BH4GLB

Sometimes, when transmitting with the ALC100, it continuously transmits without any power output. Even after adding a magnetic ring and an inductor (using JTDX), there are still occasional issues. Currently, restarting the radio seems to resolve the problem.

闽ICP备2021006864号-7

闽公网安备35020602002794号互联网举报中心

用户协议隐私政策社区规范积分规则中继规则转载须知
更新日志联系我们常见问题友情链接运营报告赞助

浩奇科技（厦门）有限公司

是无线电，把我们联系在一起